Blow molding wall thickness is rarely even from neck to base. The resin moves farther in some zones than in others, and those zones are where bottles go thin. This page is for process and QC staff who need to find those spots and keep them under control.
Why blow molded walls are uneven
In extrusion blow molding, a parison hangs and then blows out to the mould. Areas that must travel farther end up thinner. Areas that travel less, or that receive more melt, end up thicker.
The same wall can also vary around the circumference, because the parison is not a perfect tube and the mould is not a perfect cylinder. Oval panels, offset necks and handles all change how far the melt has to stretch.
That is why a single reading at mid-body is a weak record. It can pass while a shoulder, a corner or a base pinch-off is already thin.
Extrusion vs injection stretch blow molding
Extrusion blow molding is the usual route for HDPE and PP bottles, including many handled and oval packs. Wall distribution starts with the parison and with how it sags and blows. Programming the parison profile is the main process lever.
Injection stretch blow molding is the usual route for PET bottles made from preforms. Wall distribution starts with the preform and with how the stretch rod and the blow move the resin. This page stays with extrusion blow molding. PET is mentioned only so the two routes are not mixed up.
If your plant runs both, keep the records on separate forms. A thin zone on a parison-blown bottle and a thin zone on a stretched preform do not have the same cause.
Thin spots at shoulders, corners, base and handles
The zones that usually run thin are easy to name once you watch a few lots.
Shoulders thin where the neck opens into the body and the melt has to turn and stretch. Corners and heels thin where the body folds into the base. The base pinch-off can be thinner than the base beside it if the mould faces do not leave enough resin in the weld.
Handles and the roots of handles are another risk, because the melt has to fill a narrow path and then blow out beside it. Wide flat panels on oval bottles blow out farther than the narrow sides, so the broad face often reads thinner.
For a closer look at one common resin, see HDPE bottle wall thickness. The thin zones on PP and other polyolefin bottles follow the same logic, even when the feel of the wall is different.
Want to see a wall thickness check on a bottle like yours? Tell us what you need to test. We test a similar material sample and send you the video, so you do not need to ship a sample. If you prefer to send your own, we accept that too.
Process levers of parison programming, temperature and stretch
Parison programming is the first lever. You thicken the melt in the zones that will stretch the most, and you thin the zones that would otherwise run heavy. The profile has to match the mould, not a memory of a different bottle.
Melt temperature and mould temperature come next. A hotter, more fluid parison sags and thins in a different pattern from a cooler one. Uneven heating around the die makes one side of the bottle thin even when the program looks right.
Blow timing and stretch also matter. A late blow, a fast blow, or a stretch that starts before the parison is ready will move resin away from corners and shoulders. Change one lever at a time, then measure the same marked zones again.
Measuring and mapping wall thickness on the line
Mark the thin-risk zones on a first-article bottle and measure them on every sampled bottle the same way. Mid-body alone is not a map. Shoulder, panel, heel, pinch-off and handle root should each have a place on the record.
A hall-effect gauge reads wall thickness from the outside with a steel target ball inside the bottle, so you do not cut the pack. The MTG-100 hall-effect thickness gauge is built for that kind of non-destructive wall and base check on plastic and other non-magnetic bottles.
For the measuring steps, see how to measure bottle wall thickness. Application notes for plastic bottles are on the plastic bottles application page. Keep the bottle still, seat the ball, and write down the zone, not only the number.
Use the map to feed parison and temperature changes, then measure the same zones again. A change that thickens the shoulder but starves the heel is not a fix.
Frequently asked questions
Can one mid-body reading show that a blow molded bottle is in control?
No. Mid-body is often the easiest place to measure and the last place to go thin. You still need the shoulder, corners, base and any handle.
Is parison programming enough on its own?
It is the main lever on an extrusion line, but temperature, blow timing and mould condition still move the wall. If the profile is right and the bottle is still thin on one side, look at heating and the mould next.
Does a test video replace a quotation?
No. The video shows how a similar bottle is measured. A quotation still needs the instrument setup and the shipping details you ask us to include.
Get a test video for your bottles
Tell us what you need to test, such as the material, the size and the test method. We test a similar material sample on the instrument you are looking at and send you the video, so you do not need to ship a sample. If you prefer to send your own, we accept that too.
Questions about a model or a test? Email Amy Zhao, Export Manager, at [email protected].